Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

A review on ultrasonic spot welding of copper alloys

As a solid state joining process, ultrasonic spot welding has been proven to be a promising technique for joining copper alloys. However, challenges still remain in employing ultrasonic spot welding to join copper alloys. This article comprehensively reviews the current state of ultrasonic spot welding of copper alloys with a number of critical issues including materials flow, plastic deformation, temperature distribution, vibration, relative motion, vertical displacement, interface friction coefficient, online monitoring technique, coupled with the macrostructure and microstructure, the mechanical properties and electrical conductivity. In addition, the future trends in this field are provided.     

施工中电焊机的安全使用简述

从电焊机自身电气特点及建筑工地工作环境入手,探讨电焊机安全技术的实施方法。分析电焊机安全隐患及事故的分类以及电焊机在使用过程中产生危险的原因。介绍电焊机在安装以及作业过程中的安全措施。     

多运营商高铁隧道移动网络覆盖方案

高铁移动网络覆盖是国内三大通信运营商的一个重点,而高铁隧道内移动网络覆盖更是运营商的一大难点痛点。文章根据我国中部省份某高铁线路覆盖规划实例,采用“设备+POI+泄漏电缆”模式,即三家运营商信号源设备通过同一POI(point of interface,多系统接入平台)接入,信号输出到泄漏电缆进行隧道覆盖,隧道口场坪站安装宽频切换天线对隧道外进行延伸覆盖,通过链路预算合理布置各运营商主设备信号源,从而实现隧道到室外的无缝覆盖。最后,根据已有成熟网络覆盖解决方案,对未来5G高铁隧道移动网络覆盖方案进行了探讨。     

重轨矫直速度对矫后残余应力的影响分析

针对矫直速度对重轨矫后残余应力的影响进行研究,利用Pro/E建立60kg·m-1重轨九辊水平矫直模型,采用ANSYS Workbench对重轨矫直过程进行有限元数值模拟,通过现场矫直规程对采用现场矫直速度以及假定矫直速度得到的重轨矫后残余应力进行分析比较,得出了在其余条件不变的情况下重轨的矫直速度在1.4~1.6m·s-1的范围内其轨底矫后纵向残余拉应力小于250MPa,且残余应力分布合理,满足矫直要求,相比于现场采用的1.2m·s-1的矫直速度其生产效率最大能够提高16.7%~33.3%。     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

Q690钢焊接接头微观组织对冷裂纹的影响研究

分析了Q690钢手工电弧焊与气体保护焊焊接冷裂纹产生与微观组织的联系。结果表明: 焊接冷裂纹起源于斜Y坡口根部, 沿熔合区、焊缝扩展至焊缝表面;2种工艺焊接的接头组织硬度均较母材高, 而塑性较差。热影响区为马氏体、贝氏体与铁素体混合组织, 焊缝组织由先共析铁素体、侧板条铁素体、贝氏体和针状铁素体等组成, 针状铁素体抗裂纹扩展能力较其他组织强。在2种焊接方法对应断口中观察到了冷裂纹起裂、扩展与断裂区的不同形貌, 起裂与扩展区存在塑性变形, 而断裂区为解理断裂。     

转速对2524铝合金搅拌摩擦点焊组织与性能的影响

对2524铝合金薄板进行搭接搅拌摩擦点焊试验, 研究了搅拌头转速对其组织与性能的影响。结果表明, 随转速增加, 焊点外侧飞边越加严重, 组织畸变程度增加, 焊核区宽度增大, 有效连接宽度先增大后减小。母材区硬度最大, 热影响区硬度最低;在焊核区内, 显微硬度随转速增加而增大, 当转速为1 100 r/min时达到最大133.9HV, 而热影响区在300 r/min时硬度最大。在单向拉伸试验中, 接头剪切强度随转速增加先增大后减小, 在700 r/min时达到最大值3 510 N;接头呈现出两种断裂模式: 即低转速下平行于两板面断裂和高转速下沿倾斜方向断裂;断口呈现明显的剪切韧窝形态, 韧窝小而浅, 焊接接头为韧性断裂。     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Role of Cyclooxygenase-2 in Head and Neck Tumorigenesis

The cyclooxygenase-2 (COX-2) is a potent enzyme that converts arachidonic acid to prostaglandins (PG), including PGE2, a key mediator of inflammation and angiogenesis. Importantly, COX-2 is activated in response to inflammatory stimuli, where it is also believed to promote the development and progression of head and neck cancers (HNC). COX-2 can mediate its protumorigenic effect through various mechanisms, such as inducing cell proliferation, inhibition of apoptosis, and suppressing the host’s immune response. Furthermore, COX-2 can induce the production of vascular endothelial growth factors, hence, promoting angiogenesis. Indeed, the ability of COX-2 inhibitors to selectively restrict the proliferation of tumor cells and mediating apoptosis provides promising therapeutic targets for cancer patients. Thus, in this comprehensive review, we summarized the reported differential expression patterns of COX-2 in different stages of head and neck carcinogenesis—from potentially premalignant lesions to invasive carcinomas. Furthermore, we examined the available meta-analysis evidence for COX-2 role in the carcinogenesis of HNC. Finally, further understanding of the biological processes of COX-2 and its role in orchestrating cell proliferation, apoptosis, and angiogenesis may give therapeutically beneficial insight to develop the management plan of HNC patients and improve their clinical outcomes.